Konstruktionsteknik Jobs

I need a structural engineer experienced in industrial steel warehouse and shed design to design a lightweight and economical MS structure using mainly C-channels and RHS/box pipes, suitable for fabrication and erection in India. Project Details Building size: 145 ft × 55 ft Building type: Industrial warehouse Roof: Double-slope / gable roof Clear height: 10,365 mm (approximately 34 ft) Roofing: JSW 0.60 mm PPGI profile sheet Vertical cladding: JSW 0.60 mm PPGI profile sheet Brick masonry: 3 m high brick wall on all sides Crane: 5-ton EOT crane Structure: MS steel Design objective: Lightweight, economical and structurally safe Preferred Structural System I specifically want the structure optimized using C-channel or built-up C-channel columns, RHS/box-pipe roof trusses, ...

I need help with a new HVAC unit that is making excessive loud air flow noise at the return duct. This issue was noticed immediately after installation by the builder during new construction. Ideal Skills and Experience: - HVAC installation and troubleshooting expertise - Experience with noise reduction solutions - Ability to diagnose and correct airflow issues

I need engineering-certified documents for a 3.5 meter tall composite privacy fence. There would be two parts to the fence - one 6 meters long and one 8 meters long. It was suggested to me that we use 75*75mm galvanised poles and the 8 meter wall would need 5 posts and 6 meter wall would need 4 posts. The top part of the fence can have any screening material (including with more than 50% wind loading). Happy to discuss any screening products for the top part of the fence. The design should be simple and functional, focusing solely on privacy. Key Requirements: - Engineering certification for tall composite privacy fence (coastal Perth area) - Privacy-focused, minimalistic design - Compliance with local building codes and regulations Ideal Skills and Experience: - Structural engineering ...

I have a project underway in Americus, Georgia that requires a formal Standard Proctor compaction test on the clay soils within the foundation footprint. The excavation will be open and accessible, so you can collect representative samples on-site without delays. Your scope is straightforward: perform the field sampling, run the laboratory Standard Proctor, and deliver a stamped report summarizing optimum moisture content, maximum dry density, and any recommendations if the results fall short of specification. Please include photographs of sampling locations and note test procedures followed (ASTM D698). Timing is important—we are targeting next week, but I can coordinate around your lab schedule if needed. Bring any necessary field tools; site access and safety briefing will be ...

I need a full engineering design for a bored cast-in-situ pile, 600 mm in diameter and 21 m deep, capable of carrying 175 tonnes. The piles will support a multi-storey commercial building to be erected on sandy soil, so the design must reflect both the reduced shaft friction typical of this stratum and the higher potential for scour near the surface. Please include all geotechnical and structural calculations, load-settlement analysis, reinforcement detailing, and a clear layout plan showing pile spacing, cut-off levels, and cap geometry. I also expect a concise design report referencing the governing code you choose (IS 2911, ), together with editable drawings in DWG or REVIT and a sealed PDF set ready for permitting. Deliverables: • Design brief with assumptions and safety factors...

I'm seeking an expert to perform load bearing analysis on a building structure. Requirements: - Analyze structural integrity under various loads. - Provide detailed reports and recommendations. - Utilize industry-standard software. Ideal Skills: - Proficiency in structural engineering principles. - Experience with load bearing and FEA. - Strong analytical and documentation skills.

I'm seeking a skilled construction designer to create precise designs for sidewalks and ramps. Key Requirements: - Accurate measurements and angles - Detailed CAD designs Ideal Skills and Experience: - Expertise in construction design - Proficiency in CAD software - Experience with sidewalks and ramps design

I need a complete masterplan and construction-ready drawing package for a new 100,000 m² container yard. The design must revolve around smooth, conflict-free circulation—optimising traffic flow is my top priority—while still extracting the maximum operational value from every square metre. Scope of the yard Please incorporate all functional zones and structures listed below, laid out logically to keep heavy, light and pedestrian movements separated wherever practical: • Loading / unloading zones • Container blocks (full, empty and reefer), complete with reefer power points • Inland container depot space 40,000 square meters, empty container yard 25,000 square meeters and export CFS 15,000 square meters • Lorry holding / marshalling parking area...

I'm looking for a skilled carpenter or builder to construct a 10x20 lean-to greenhouse. The primary purpose of this greenhouse is to start seedlings. Requirements: - Structure must be made of wood - Covered with polycarbonate panels Ideal Skills: - Experience in greenhouse construction - Proficiency in woodworking - Knowledge of polycarbonate panel installation

I need detailed building permit drawings and specifications for rebuilding a partially damaged garage brick wall. The wall needs to be completely rebuilt. Engineer must be licensed in the state of Pennsylvania, USA and have experience working on projects (including preparing building permit documents) in Philadelphia, Pennsylvania. Photos and a preliminary report from a structural engineering are available and can be provided to qualified, Pennsylvania licensed and experienced structural engineers who express interest in the project. Requirements: - Accurate and compliant drawings for building permit - Detailed specifications for reconstruction Ideal Skills and Experience: - Proficiency in architectural drafting - Knowledge of local building codes and permit requirements - Experience wit...

I am looking for an experienced **Residential Construction Estimator / Material Takeoff Specialist** to complete a detailed material takeoff from a full set of residential construction plans. I need someone who can carefully review the drawings and provide accurate quantities for the materials required for construction. The takeoff should include, as applicable: * Framing lumber * Floor and roof framing * Wall, floor, and roof sheathing * Engineered lumber/LVLs * Roofing materials * Drywall * Exterior siding * Concrete/foundation materials * Other major building materials shown on the plans The final takeoff should be clearly organized by category and include quantities, sizes, lengths, and specifications where applicable. I would prefer the final takeoff in Excel or another clearly or...

Pentru o stație de transformare ce integrează și baterii de stocare a energiei am nevoie să fie întocmită, la nivel de proiectare, întreaga Carte Tehnică a Construcției aferentă instalațiilor electrice. Documentația trebuie structurată conform legislației române (inclusiv HG-urile și normativele tehnice specifice) și să acopere toate capitolele obligatorii – de la memoriu tehnic, scheme electrice, calcule de dimensionare și liste de echipamente, până la planșe, referate de verificare și fișe de încercări. Caut un specialist care să: • elaboreze sau completeze desenele și calculele necesare unei stații de transformare, având în vedere și integrarea sistemului de baterii; • organizeze documentele într-un format unitar, numerota...

I’m purchasing a home and the appraisal requires a structural engineer to evaluate the foundation/structure. I’m looking for an independent evaluation and written documentation of the findings to provide to my lender. Is this something you provide? If so, could you let me know the cost and your earliest availability? Location is 44904.

Confirmis () is a Singapore-based business information provider specializing in connecting businesses with global capabilities; comprised of industry veterans, Confirmis's business model is designed to overcome perennial lack of data (let alone quality data) to support effective decision-making, particularly in developing economies. As a Site Verifier, you will be responsible for verifying a residence existence through visual data by conducting a site visit to ensure that we provide reliable and accurate information to our client. JOB DESCRIPTION: • Take pictures of the residence and its vicinity per Confirmis’ standard operating guidelines. • Take picture of the surrounding area and provide observation about the residence REQUIREMENTS: • Must be living in (or ...

I need structural calculations for façade lighting at Al Kaloti Tower, Sharjah. This involves assessing a 3.6m aluminium channel fixed to 150mm GRC using 3×M8 Fischer chemical anchors and also for the led light fixation on the grc using the same fixing method Key factors to evaluate include: - Wind load -Wind load pressure shall be based on the wind tunnel report. - Pull-out strength - Tensile strength - Shear strength Detailed sketch/drawing to be provided showing the dimensions, fixation details, location of fixation in GRC & distance from edge. Proposed Anchor bolt/screw data sheet shall be provided with highlight at the capacity in tension & shear. Chemical Anchors shall be used as recommended by the GRC Subcontractor, the proposed anchor bolts are mechanical a...

Ich suche einen erfahrenen Fachplaner, der für ein Gewerbegebäude in München ein vollumfängliches Brandschutzkonzept erstellt und bis zur behördlichen Genehmigung begleitet. Was ich konkret benötige • Erfassung und dokumentation des ist-Standes • Erarbeitung eines schlüssigen, genehmigungsfähigen Brandschutzkonzepts inklusive aller relevanten Berechnungen und Pläne • Kostenschätzung • Abstimmung mit den örtlichen Behörden und der Feuerwehr, um Nachfragen zügig zu klären • Übergabe sämtlicher Planunterlagen als editierbare CAD-Dateien sowie als PDF für den Bauantrag Rahmenbedingungen Die Immobilie ist ein mehrgeschossiger Industriebau mit Produktions- und Lagerbereichen...