NASA Contest: Design a “Smart” Attachment Mechanism

  • Status: Closed
  • Pris: $1500
  • Bidrag mottagna: 17
  • Vinnare: Myrds

Tävlingssammandrag

Design a “Smart” Attachment Mechanism (no positioning capability) (SAM)

In this challenge, you are asked to design a “Smart” Attachment Mechanism (SAM) that will be mounted to the free end of a separately designed robotic arm. The SAM receives all external power and high-level commands through its interface to the robotic arm, but implements the below functions autonomously.

How it works: Initially, the SAM will be packed in a stowed configuration. Once activated, the SAM must be capable of autonomously performing five high-level actions:
1) unpack itself in preparation for placement near a Handrail,
2) close on the Handrail,
3) maintain a hold on the handrail for an extended period of time,
4) release from the handrail, and
5) pack back into the initial stowed configuration.

Click on the attachments below to see
1) the SAM Problem Description, which provides more detailed instructions about all the requirements your design needs to meet;
2) SAM Solution Guidelines, which details the format an content that your submission must follow; and
3) the templates that are referenced in the solution guidelines. Microsoft Excel and Open Office Calc formats are attached below.

Challenge rules:
The prize will be awarded for the lowest mass, technically feasible solution, submitted by the contest deadline.
No working prototype is required for submission, but the design must be sufficiently detailed to allow experts to assess the feasibility of your design (i.e., comply with all requirements) and the credibility of your mass estimate.
Only complete submission packages will be evaluated (see attachments).

NASA may select multiple winners or provide additional prize compensation on entries that are particularly novel or innovative.

NASA will be available to respond to clarifying questions, but feedback on quality is otherwise limited.
All complete submissions will be confirmed with 3-star ratings.
Note that final judgement of quality and winners will only happen after the submission deadline.

Rekommenderade kompetenser

Arbetsgivares feedback

“Myrdal M. developed an innovative design for a robotic "smart" attachment mechanism. This was a contest and this design was selected from 18 entries as the most feasible and least mass design. Myrdal M. provided an impressive design submission and has been very responsive in providing everything that is needed. ”

Profilbild nasacoeci, United States.

Topp bidrag från den här tävlingen

Visa fler bidag

Klargörandetavla

  • nasacoeci
    Tävlingsinnehavare
    • 5 år sedan

    We have launched 4 new challenges and are updating the landing page shortly: https://www.freelancer.com/contest/NASA-Contest-Design-an-Electrically-Driven-Clamp-1328523.html https://www.freelancer.com/contest/NASA-Contest-Design-a-Mechanically-Driven-Clamp-1328522.html https://www.freelancer.com/contest/NASA-Contest-Design-a-Smart-Coarsepositioning-Arm-1328497.html https://www.freelancer.com/contest/NASA-Contest-Design-a-Smart-FinePositioning-Arm-1328489.html

    • 5 år sedan
  • Myrds
    Myrds
    • 5 år sedan

    I don't have much to say but thank you.

    • 5 år sedan
  • nasacoeci
    Tävlingsinnehavare
    • 5 år sedan

    Please join us in congratulating Myrdal M. as the winner for this challenge. Thanks to all of the participants for all of your hard work on this challenge. There were some really great designs and the evaluation was not easy. We hope that many of you will participate in the rest of the challenges that we will be posting over the next couple of months.

    • 5 år sedan
  • fbcouto
    fbcouto
    • 5 år sedan

    My submission code 78763.

    • 5 år sedan
  • nasacoeci
    Tävlingsinnehavare
    • 5 år sedan

    FYI....We have opened our next contest :"Design a Positioning Software Architecture" at https://www.freelancer.com/contest/NASA-Contest-Design-a-Positioning-Software-Architecture-1328512.html.

    • 5 år sedan
  • nasacoeci
    Tävlingsinnehavare
    • 5 år sedan

    This contest is now closed. Thank you for all of your hard work on some really great designs. The team will be evaluating the submissions and announcing the winners as soon as we can (likely about a week). There are several other contests currently active with even more launching over the next few months. We look forward to seeing more of this amazing talent! Thanks!

    • 5 år sedan
  • ilirjanleci
    ilirjanleci
    • 5 år sedan

    Hello,due to some issues i cant deliver a whole project (the kinematics) but i have the design of it,can this be considered ?

    • 5 år sedan
    1. nasacoeci
      Tävlingsinnehavare
      • 5 år sedan

      Designs must be complete per the submission guidelines (attached to the contest description page). We recommend that you try and complete as much of the required work as possible and submit what you have. Just be aware that there are minimum requirements that must be met in order for the submission to be evaluated and eligible for award.

      • 5 år sedan
    2. ilirjanleci
      ilirjanleci
      • 5 år sedan

      The design by idea met all requirements, but right now i cant confirm it by kinematics,i cant deliver it like this but i can use it for the spam. Great contest though,thank you !

      • 5 år sedan
  • nasacoeci
    Tävlingsinnehavare
    • 5 år sedan

    Only 2 hours remain for this contest. Please make sure and read the submission guidelines and include all of the required items. Many people are leaving off the Exit Survey code which is required for your submission to be eligible for evaluation and award. We recommend not waiting until the last minutes before the deadline to upload your submission. Submissions that are late (or can't be submitted) due to upload errors or site issues will not considered.

    • 5 år sedan
  • junkmailhater
    junkmailhater
    • 5 år sedan

    #lastminuteentry Hi there I hope I am not to late with my last minute entry. Actually I am kinda lucky to have this contest extended as I saw the contest with like 10 hrs to go from the original deadline. Have a nice day thanks!

    • 5 år sedan
  • nasacoeci
    Tävlingsinnehavare
    • 5 år sedan

    FYI....We have opened our next contest :"Design a Positioning Software Architecture" at https://www.freelancer.com/contest/NASA-Contest-Design-a-Positioning-Software-Architecture-1328512.html.

    • 5 år sedan
  • anandvelandy3
    anandvelandy3
    • 5 år sedan

    Hello, in AM description document section 3.2 table 1, force sensor energy cost is given as .375 W hr. Current information is unknown. Can this value be used for power profile? Or can you provide more info. Thank you

    • 5 år sedan
    1. nasacoeci
      Tävlingsinnehavare
      • 5 år sedan

      This value can be used for the power profile.

      • 5 år sedan
    2. anandvelandy3
      anandvelandy3
      • 5 år sedan

      Thank you

      • 5 år sedan
  • anandvelandy3
    anandvelandy3
    • 5 år sedan

    R2.3 normal operating load moment on handrail of 3.5Nm about y axis. Is it from the interface plate Geometric center? If so that means on handrail(at distance 58.66mm) a force of about 6 kg would be applied in Z direction on handrail . It seems too much. Is the 3.5Nm value correct?

    • 5 år sedan
    1. nasacoeci
      Tävlingsinnehavare
      • 5 år sedan

      Yep, there is a graphic showing the load and its orientation relative to the Interface Plate Geometric Center. The 3.5 Nm number of the load is based on potential astronaut loading scenarios and is correct.

      • 5 år sedan
  • Myrds
    Myrds
    • 5 år sedan

    Just to clarify, to save time in my end, since the system layout minimum requirement is not indicated. Since I use a combination of electrical, electronic and mechanical. Is it ok to ONLY use the block diagram for the system layout (not to include the mechanical exploded view and the circuit diagram). Thank you.

    • 5 år sedan
    1. Myrds
      Myrds
      • 5 år sedan

      My apologies, it is indicated in the guidelines that if I represent a combination of electrical and mechanical, the system layout should be presented by a block diagram. I apologize for overlooking this.

      • 5 år sedan
  • Myrds
    Myrds
    • 5 år sedan

    Hello, I just would like to clarify a quality issue. I am currently using a DSub part, and the shielding of the connector extended 0.735 mm from the base when packed. Meaning the shielding is already outside the accepted dynamic volume. I could not move the connector upward for it will misalign with the given connector mate. Though it is a part, I could negative extrude the 3D to remove the excess, but the part won't exist anymore in the market. Please advise.

    • 5 år sedan
    1. nasacoeci
      Tävlingsinnehavare
      • 5 år sedan

      It is acceptable for the shielding of the standard DSUB (the outside trapezoidal shape) as well as the pins to go outside the permissible range such that they can connect with the interface plate, but for this part only. This was overlooked in the formulation of the problem.

      • 5 år sedan
    2. Myrds
      Myrds
      • 5 år sedan

      Anyway, I already edited the 3D of the DSub connector. The exceeding part was not the trapezoidal shape, but the flat part that extends. Trapezoidal shape and pins was retained to remain at standard.

      • 5 år sedan
  • ilirjanleci
    ilirjanleci
    • 5 år sedan

    #extended

    • 5 år sedan
    1. nasacoeci
      Tävlingsinnehavare
      • 5 år sedan

      Done!

      • 5 år sedan
  • anandvelandy3
    anandvelandy3
    • 5 år sedan

    #extended KINDLY consider extending.

    • 5 år sedan
    1. nasacoeci
      Tävlingsinnehavare
      • 5 år sedan

      Done!

      • 5 år sedan
  • nasacoeci
    Tävlingsinnehavare
    • 5 år sedan

    We have now extended the submission deadline for this contest to Monday, July 2nd at 12 PM Eastern Daylight Time.

    • 5 år sedan
  • ilirjanleci
    ilirjanleci
    • 5 år sedan

    Thank you for the Extension,i will make you a good one...

    • 5 år sedan
  • anandvelandy3
    anandvelandy3
    • 5 år sedan

    Extended, Great!

    • 5 år sedan
  • Myrds
    Myrds
    • 5 år sedan

    I just would like to clarify the minimum requirement for the system layout for it was not indicated in the guidelines. Is it ok if I only use a block diagram? Also, will this contest be extended?

    • 5 år sedan
    1. anandvelandy3
      anandvelandy3
      • 5 år sedan

      #extended please

      • 5 år sedan
    2. Myrds
      Myrds
      • 5 år sedan

      What I meant is to create a block diagram only, not include a block diagram , for the system layout. If this is acceptable.

      • 5 år sedan
  • Myrds
    Myrds
    • 5 år sedan

    Just to clarify, Pin 1 is ground, Pin 4 is Bus voltage, serial command using the 3rd and 2nd pins. If only 4 pins are used, does this mean that I should create my own circuit board that connects to my active components to control and receive feedback from it, while interfaced with a male D-Sub to connect with the interface plate? There are no other pins available where I could connect active components, and it is only controlled via serial connection by 2 pins.

    • 5 år sedan
    1. nasacoeci
      Tävlingsinnehavare
      • 5 år sedan

      You should design whatever components are required for your SAM design that allows it to use power and serial data through the four provided pins in that DSUB female interface.

      • 5 år sedan
    2. nasacoeci
      Tävlingsinnehavare
      • 5 år sedan

      You should create whatever you need to interpret those serial commands passed through the D-Sub Connector in the interface plate to transform the commands into motion.

      • 5 år sedan
  • Myrds
    Myrds
    • 5 år sedan

    Can I use the same Attachment Mechanism I used in the non smart version in the previous contest and just tweak it to be a smart version. Though I am still reviewing the requirements.

    • 5 år sedan
    1. nasacoeci
      Tävlingsinnehavare
      • 5 år sedan

      You may reuse your design/design elements in your submissions to other contests. Just make sure you address the contest requirements.

      • 5 år sedan
    2. Myrds
      Myrds
      • 5 år sedan

      Ok thank you.

      • 5 år sedan
  • fbcouto
    fbcouto
    • 5 år sedan

    Hello NASA, the shape of the object must be a parallelepiped or would be curve or smaller ?

    • 5 år sedan
    1. fbcouto
      fbcouto
      • 5 år sedan

      I am asking about the SAM.

      • 5 år sedan
    2. nasacoeci
      Tävlingsinnehavare
      • 5 år sedan

      The SAM may take any form you desire, as long as it meets the functional requirements.

      • 5 år sedan
  • phaser6250
    phaser6250
    • 5 år sedan

    Hello NASA, What exactly does "smart" mean in the context of these projects? Some of the contests are listed as "no smarts", so what exactly does it mean?

    • 5 år sedan
    1. nasacoeci
      Tävlingsinnehavare
      • 5 år sedan

      In the context of these projects, "smart" means that that your solution will have to interpret serial commands and react accordingly.

      • 5 år sedan
  • macoronas
    macoronas
    • 5 år sedan

    Appriciate it!

    • 5 år sedan
  • macoronas
    macoronas
    • 5 år sedan

    Is there a way that you can further prove that your identity as a NASA contest holder & reputation as Freelancer employer is authentic?

    • 5 år sedan
    1. nasacoeci
      Tävlingsinnehavare
      • 5 år sedan

      Sure. Visit our NASA Tournament Lab webpage where we describe this series at the nasa.gov official NASA Site: https://www.nasa.gov/feature/astrobee-challenges-series

      • 5 år sedan

Visa fler kommentarer

Hur du kommer igång med tävlingar

  • Lägg upp din tävling

    Lägg upp din tävling Snabbt och enkelt

  • Få massvis med bidrag

    Få massvis med bidrag Från världens alla hörn

  • Utse det bästa bidraget

    Utse det bästa bidraget Ladda ner filerna - enkelt!

Lägg upp en tävling nu eller gå med idag!