minor alterations to SLDASM file to allow sensors window to align to sensors

  • Status: Closed
  • Pris: £8
  • Bidrag mottagna: 4
  • Vinnare: DSeryani

Tävlingssammandrag

work.
1. Small amendments to the design of an enclosure to fit pcb, electronics board. Task is delivered when you provide acceptable to owner, an;
• amended STEP/ SLDPRT file ‘Bottom_2018’
• extruded Small Board SENSORS V1.2.STEP or SLDPRT
read file for complete task A, B, C.
File outputs to be fully viewable and amendable by Fusion 360

Rekommenderade kompetenser

Arbetsgivares feedback

“I found Daniel highly diligent in wanting to complete these design alteration tasks. Quality of what was produced and Accepted was 5*. The fact he didnt complete on one task D is down to a definition error accepted by us both as meaning something different. It is also important for the hirer to make sure Daniel can actually operate with all file types supplied as a .dxf caused issue. On balance with straight forward tasks i would hire again. ”

Profilbild birddog98, United Kingdom.

Topp bidrag från den här tävlingen

Visa fler bidag

Klargörandetavla

  • asdhone4
    asdhone4
    • 5 år sedan

    good work

    • 5 år sedan
  • DSeryani
    DSeryani
    • 5 år sedan

    I understand what sort of changes you need made. It seems like the PCB goes into the case and you need some sort of standoffs to mount it on as well as some windows. However the drawing you provided is not dimensioned enough for me to make a new model of the PCB. Also, if you intend on injection molding this cover, you would need to redesign anyways. The way you have the clip cannot be reached with tooling. Also, this might need a bit of a prize increase. If you want to redesign the cover and want me hourly or per project, please do contact me.

    • 5 år sedan
    1. birddog98
      Tävlingsinnehavare
      • 5 år sedan

      ok , your point ' if you intend on injection molding this cover, ' non worries, this is prototype 3d printed and then we are redesigning and moving on from it.

      • 5 år sedan
    2. DSeryani
      DSeryani
      • 5 år sedan

      I can suggest an awesome manufacturing technique for low-cost production without injection molding tooling. Its way better than your traditional FDM 3D Printing and your part will work well with little modification.

      As far as the DXF goes, you dont have dimensions such as the height of the chip and the width of the three sections or the height of the angled lines maybe. All of that helps in putting together a 3D model.

      • 5 år sedan
  • birddog98
    Tävlingsinnehavare
    • 5 år sedan

    To convert a Solidworks file format to a DWG file format in AutoCAD: At the command prompt, type IMPORT and press Enter. In the Import File dialog box, "Files of type" drop-down list, select "Solidworks (*.prt; *.sldprt; *.asm; *sldasm)." Find and select the Solidworks file you want to convert and click Open.

    • 5 år sedan
  • birddog98
    Tävlingsinnehavare
    • 5 år sedan

    NB the odg file is from Libreoffice, equivalent to Powerpoint

    • 5 år sedan
  • engyoussief
    engyoussief
    • 5 år sedan

    #increaseprize

    • 5 år sedan
  • gupta9665
    gupta9665
    • 5 år sedan

    The part files are missing and without them changes can not be made. Also there are two parts in the assembly file, so advise as which one should be modified OR both of them should be modified.

    • 5 år sedan
    1. birddog98
      Tävlingsinnehavare
      • 5 år sedan

      Solidworks file uploaded. Only the case is to be modified. description is clear.

      • 5 år sedan
    2. birddog98
      Tävlingsinnehavare
      • 5 år sedan

      Hi Deepak, kindly re check project. all files been updated.

      • 5 år sedan
  • jhosser
    jhosser
    • 5 år sedan

    Greetings, you can send another type of file or an image

    • 5 år sedan
    1. birddog98
      Tävlingsinnehavare
      • 5 år sedan

      done

      • 5 år sedan
    2. birddog98
      Tävlingsinnehavare
      • 5 år sedan

      Hi Jhosser, kindly re check project. all files been updated.

      • 5 år sedan
  • dedierwanto2686
    dedierwanto2686
    • 5 år sedan

    Hi CH, can you upload the sldprt file? this sldasm file can not be opened

    • 5 år sedan
    1. dedierwanto2686
      dedierwanto2686
      • 5 år sedan

      sorry i can't opened PC file,can you shared file pcb with format file step or sldprt?

      • 5 år sedan
    2. birddog98
      Tävlingsinnehavare
      • 5 år sedan

      Hi Dedy, kindly re check project. all files been updated.

      • 5 år sedan

Visa fler kommentarer

Hur du kommer igång med tävlingar

  • Lägg upp din tävling

    Lägg upp din tävling Snabbt och enkelt

  • Få massvis med bidrag

    Få massvis med bidrag Från världens alla hörn

  • Utse det bästa bidraget

    Utse det bästa bidraget Ladda ner filerna - enkelt!

Lägg upp en tävling nu eller gå med idag!